Products

White
Brushed Metal (+10$)

Edge

Square Recessed Light

$104.99 USD
White
Brushed Metal (+10$)

Radius

Round Recessed Light

$104.99 USD

Hub

Central Control

$84.99 USD
Black
Brushed Metal (+10$)

Profile

Wall Light - Outdoor/Indoor

$204.99 USD

Halo

Tracklight

$309.99 USD

Impression

Ambience Light

$94.99 USD

Signal

Water Leak Sensor

$84.99 USD

Control

Light controller

$59.99 USD

Thermostat

Thermostat

$199.99 USD

Convector

Convector

$399.99 USD

Control

Light controller

Support topics

Control FAQ

Do I require an Electrician to install the Light controller?

You do not require an Electrician to install the Light controller as it includes a simple Decora switch kit and a simple Toggle switch kit. You can also install the Light controller on your wall using included stickers. The step by step process is included in the user-manual.

How should the switch kits be installed?

The Smartika Logo should always be upwards. The remote and the support-kits includes a magnet therefore the Light controller can be installed practically anywhere.

What controls does the Light controller offer?

The Light controller includes an ON and OFF Button.
If you press the ON button, the lighting will be at the last setting.

The Light controller includes 2-intensity buttons shown by icons. (INCREASE OR DECREASE)
The settings included are from 5% lighting intensity to 100% intensity.
If you want to get 0%, you need to press on OFF button.

The Light controller includes 2 Dimming buttons shown by icons. (WARM or COLD)
The settings included are from 2700K (warm lighting) to 5000K lighting (cold lighting).





How should I touch the Light controller buttons?

For the ON or OFF button
A simple click be enough, the remote will make a clicking sound

For the Smartika AmbienceShift technology (WARM or COLD)
Keep your finger on the right or left button as the light fixture modifies the settings. You can also press the button multiple times to achieve desired results.

For the Smartika SmoothDimming technology (DIMMING)
Keep your finger on the up or down button as the light fixture modifies the settings. You can also press the button multiple times to achieve desired results.

What kind of batteries does the Light controller require?

For battery replacement, use CR2032 lithium battery only.

How will I know if the Light controller battery is low on power?

In the Smart mode, the Smartika Application will send you a notification and/or an email.

Can I use the Light controller included with the Halo light fixture with other lighting devices?

Yes, you can use the Halo light fixture Light controller with any other Smartika lighting device.

How many devices can a Light controller control?

Smart Mode
One Light controller device can control 19 devices within a group using the mobile application.

Conventionnal Mode
You can control one device at a time with your Light controller. 

In conventional mode, how do I Synchronize the Light controller with a Light fixture?
  1. Press the sync button on the light fixture. The sync button will flash.
  2. Using a needle or the tip of a paper clip, press the sync button on the light Light controller;
  • Located behind the Light controller, there is a small hole located under the Smartika Logo
  • Perform a Quick press only using the tip of a paper clip (listen closely and you should here a faint clicking sound) 
  • The device-light will stop flashing once the device and the light Light controller will be synchronized. 
  • After completed, you can use the Light controller.

NOTE: The sync flashing-light process may take up to one minute.

In conventional mode, if Light controller is synched with one device, how do I re-synch to a different device?
  1. Press the sync button on the light fixture. The sync button will flash.
  2. Using a needle or the tip of a paper clip, press the sync button on the light Light controller;
  • Located behind the Light controller, there is a small hole located under the Smartika Logo
  • Perform a Quick press only using the tip of a paper clip (listen closely and you should here a faint clicking sound) 
  • The device-light will stop flashing once the device and the light Light controller will be synchronized. 
  • After completed, you can use the Light controller.

NOTE: The sync flashing-light process may take up to one minute.

(Conventional Vs. Smart Mode) What happens if a Light controller is synched with one device yet grouped with different devices into the application?

Smart Mode

  1. When the hub is operational, the Light controller will only control the group with devices that contains the Light controller.
  2. If the hub has no internet, then the Light controller will only control the lighting device or group that is synched to it. 
  3. If the hub is not operational (No power). Nothing works.

Conventional Mode

The Light controller controls the paired light device (only one).

 

Installation Instructions

Decora - 1

Unscrew the 2 screws on the switch.

control-instruction-decora-1

Decora - 2

Screw the mounting bracket on the light switch. Make sure the light switch is ON.

control-instruction-decora-2

Decora - 3

Clip the magnetic plate on the mounting bracket.

control-instruction-decora-3

Screwless - 1

Place the 4 stickers on the mounting bracket, then stick it to the wall or the switch.

control-instructions-screwless-1

Screwless - 2

Insert the magnetic plate on the mounting bracket.

control-instructions-screwless-2
Want to know what’s new ? Access the latest release notes. Release notes

Ask for a replacement part

Send us your request by filling up the form below

Personal informations

Product informations